Thousands   Reviews Online
Lifetime Warranty  
for continental US and Canada
Same Day Shipping  
Go
Laptop Screens MADE BY LG, PHILLIPS, AUO,
SAMSUNG, HANNSTAR, CHI-MEI Details
1-855-630-1111
+1-206-299-0699 outside of continental US and Canada
  Live Chat   Offline
M-F 3am - 9pm.
S-S 11am - 7pm Eastern Time
  Support  
We ship from:
Free US and Canada shipping for 10+ screens orders
Our inventory is live, over 134400 screens in stock!

LCD Screen Installation

***Video tutorials displayed first, for step-by-step photo-guides please scroll down***

This first video is a must see for getting a general idea on the process of screen replacement:




Here is a Mac Book Pro 15" Screen changing instructions video:




Dell step by step screen replacement:




IBM ThinkPad step by step screen replacement:




Acer step by step screen replacement:




Toshiba step by step screen replacement:




ASUS step by step screen replacement:




SONY step by step screen replacement:




And here are the printed step-by-step instructions on LCD replacement.

(For links to instructions about Apple laptops scroll down to the bottom of this article.)

Laptop LCD-CCFL Screen Installation step-by-step guide

Here we have a Dell latitude D520, but these instructions are applicable to most typical laptops

IMPORTANT! Laptop internal parts, cables and sockets are very fragile and are easy to crack, to rip off or to brake. Please be extra careful.
It is also a good idea to use some sort of organizer to organize screws by the steps of disassembly so you can follow the process in reverse order when assembling the screen.


1) Make sure to disconnect the power and remove the battery before changing the screen.
Failure to remove all sources of power may result in permanent motherboard damage.




2) Using a pick or a flat screw driver pick out the rubber/plastic screw covers.
Make sure to check all the rubber covers for screws.
As well there might be extra covers and screws on the sides of the display assembly.




3) Remove all visible screws from the front of the bezel. Sometimes there might be screws on the sides as well.
It is recommended to place the screws in order of disassembly, to keep track of the correct locations.




4) Make sure all the screws are removed and proceed to remove the bezel.
Bezel is a plastic frame covering the internal mountings of the LCD panel.
It is fairly fragile and should be treated with care.




5) Starting from the side, carefully pry the plastic away from the screen.
On some laptops it is easier to start from the bottom.
Much force is not necessary but if you encounter difficulty, move a little bit further, try a different spot.
The bezel will unsnap. You may need to slide laptop lid latch to completely remove the bezel.




6) The bezel snaps out fairly easy, if it seems too difficult, make sure you haven't left any screws in.
As well make sure you are not pulling on any internal cables.
Some times the bezel might be glued to the LCD panel,
In these cases using an exact-o-knife to cut the glue will keep the bezel in good condition.




7) Remove the small screws holding the LCD panel in. There are typically 4 on each side.
Sometimes a few other screws may need to be removed from the LCD frame, in order to gain access to the main mounting screws.




8) Four screws on the left and four screws on the right.
On this model the mounting screws are easily accessible, on some laptops
You would need to free up the frame first.




9) Tilt the screen towards the keyboard, and carefully lay it down.
Make sure the Wi-Fi cables, WebCam cables and a microphone cable are not getting caught/pulled on.




10) Disconnect the video connector by gently squeezing the tabs on both sides and pulling away from the circuit board.
ATTENTION: Video connector is very fragile, take your time, if broken, the entire
Video (LVDS) Cable would need to be replaced, resulting in delay to the repair.




11) Disconnect the inverter connector. It may look different on other laptops. As well laptops which use LED back-lit screens do not have an inverter.
On this laptop the inverter is attached to the LCD panel, and has to be removed to be reused with the new panel.




Below are a few extra pictures of what the inverter looks like and how to disconnect the LCD panel from it.

Inverter connected to the LCD panel:




Gently pull the inverter connector out:




That is what the typical inverter connector looks like (Note: LED screens don't use an inverter):




12) Once the LCD panel is free from connections, pull it out and dispose of.




End of disassembly




New panel installation process.

Important! Most replacement panels ship with protective film,
it needs to be removed during the installation.


1) Reconnect the video cable on the new panel.
Make sure to align it properly, and don't use too much force.




2) Push in the inverter connector,
Again, be extra careful with all the connectors.




3) Align the LCD panel with the frame and secure the top corner screw first.
Make sure that no Wi-Fi, Camera or Mic cables are in the way.




4) Secure the LCD mounting screws on the other side, starting from the top corner screw.




5) Using both hands snap in the bezel starting from the bottom,
Move to the top consistently snapping the bezel to the display assembly.




6) Replace all bezel screws and reinstall the rubber/plastic screw covers.
Extra adhesive may be required to achieve proper fit.




7) Reinstall the battery and reconnect the power,
Then boot the laptop up, if the start up graphics appear, the screen is properly installed and working.


Additional information for Dell laptops:
Link to Dell Service Manuals

Once there, follow these steps:
Select Model>Laptops>Your Laptop model>Select product model>Manuals>Select language>Service manual>View


Links to Apple manuals, that can be downloaded for free:
- Macbook 13"
- Macbook Air
- Macbook Pro 15"
- Macbook Pro 17"
- PowerBook 17" and MacBook Pro 17" ( how to open the lid)
- PowerBook 15"
- PowerBook 17"