LCD-Bildschirm Installation

WICHTIG! Laptop inneren Teile, Kabel und Steckdosen sind sehr zerbrechlich und leicht zu knacken, abzureißen oder zu bremsen. Bitte seien Sie vorsichtig. Es ist auch eine gute Idee, eine Art Organizer verwenden, um Schrauben durch die Schritte der Demontage zu organisieren, so dass Sie den Prozess in umgekehrter Reihenfolge beim Zusammenbau der Bildschirm folgen kann. Einige Hersteller bieten Schraube und Teile Karten, diesen Prozess zu unterstützen.

Für Links zu Anleitungen zum Apple Laptops Bildlauf bis zum Ende dieses Artikels.

Erste Übung
Wir haben Toshiba Satellite Notebook für dieses Tutorial, es kann jedoch leicht für die meisten anderen Marken und Modelle von Laptops angepasst werden.
Vorbereitung: Vergewissern Sie sich, Ihren Laptop vom Netz getrennt wird, und Sie haben Ihre Batterie entfernt. Der gesamte Prozess sollte 15-20 Minuten dauern und erfordert nur einen kleinen Phillips-Schraubenzieher, ein Messer und ein weiches Tuch.
1. Hinweis Standorte der Schraube abdeckt (sie sind aus Kunststoff oder Gummi). Meist sind sie auf der Spitze des Lünette, die vordersten Teil des Bildschirms Montage
Und hier sind die gedruckten Schritt-für-Schritt-Anweisungen auf dem LCD-Ersatz.

WICHTIG! Laptop Innenteile, Kabel und Steckdosen sind sehr fragil und leicht zu knacken, um Abzocke oder zu bremsen. Bitte seien Sie vorsichtig. Es ist auch eine gute Idee, eine Art Veranstalter nutzen, um Schrauben durch die Schritte der Demontage so zu organisieren, können Sie den Vorgang in umgekehrter Reihenfolge beim Zusammenbau der Bildschirm folgen. Einige Hersteller bieten Schraube und Teile Karten, um diesen Prozess zu unterstützen.

Für Links zu Anleitungen zum Apple-Laptops scrollen zum Ende dieses Artikels.

How to replace LCD on a laptop (Inspiron 15 5000)

This is a guide on replacing an LCD on a Dell Inspiron 15 5000 Series.




Picture guide below:

For the replacement process we’ll need the following tools:

- a Phillips screwdriver
- and an X-Acto knife

To begin, shut down the laptop and disconnect the power cord.

Next step is to remove the bezel. Start from the left side. Pull the inner edge away from the glass. Once the edge is unsnapped proceed to the left top corner.

Move along the perimeter to the right side. And to the bottom. Set the bezel aside.

Now we have access to the LCD panel. Remove four phillips screws holding the screen in place. One screw in each corner.

Place the LCD panel on the keyboard. Using an X-Acto knife peel off the tape securing the video connector.

Open the connector’s bracket. Using both hands gently disconnect the video connector. Discard the old panel.

Take the new LCD screen and place it on the keyboard. Using both hands reconnect the video cable. And close the bracket.
Secure it with the protective tape.

CAUTION! It is very important not to force any of the connectors. As well you must not twist or slant the connector when plugging it in.

Lift the screen up aligning it with the screw holes.

Replace the four phillips screws.

Replace the bezel. Start at the bottom
corners, then go around the perimeter snapping the tabs in place.

Snap the tabs near the hinge cover by supporting the back cover with one hand and firmly pressing on the front with the other.

Turn the laptop on. If the start up graphics appear the replacement screen is installed correctly and we are done!